Top Article

 

 

We've stumbled upon this great article involving A Step-by-Step Guide to Installing a Bathtub listed below on the net and felt it made good sense to discuss it with you here.

Installing a bathtub isn't precisely brain surgery, but it does need strong plumbing, carpentry, and often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately challenging job. If the old bathtub is easily obtainable, the project can move quickly; if you have to open up a wall surface to get rid of the old bathtub and also position the brand-new bath tub, the job is much harder. In either case, the job is within a residence handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to consider using one prior to you start. Opportunities are you may need a professional plumber to make tube connections.
This article will assist you set up a new tub in your restroom if you have actually currently gotten a brand-new bathtub and also do not require to alter the plan of your previous supply of water pipes.
Your tools and also product checklist should consist of the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Blade


• Tape Measure


• Pipe Caps


 

Removing Old Taps

If you require to change old taps with new ones as a part of your setup, then the first thing you need to do is disconnect the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have actually been removed, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, then you will certainly require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in location between the tap and also the sink. Safeguard the faucet in place with the producer provided backnut. When the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former kind must be linked to the tap finishes initially, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Installing the Bath tub

Utilizing the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto four tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and also changing the feet on the bathtub up until the spirit level checks out level.
To mount taps, fit all-time low of the furthest versatile tap connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water system and inspect all joints and also new pipework for leakages and tighten them if needed. Fill the tub as well as also inspect the overflow outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub ought to wait up until the tub has been used a minimum of once as this will settle it into its final position.

 

 

Preparing for the Installation

Firstly, the sustaining frame provided with the bath needs to be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Use the nut provided by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath need to now be ready to be suited its final placement.

 

 

Tiling Around the Tub

In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall surface between the bathroom and the tiling, causing issues with moisture and also feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also can sealing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bath tub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant glue and also grout.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I was made aware of that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through someone on our other web address. Are you aware of somebody else who is excited by Tools You Need to Install a New Bathtub ? Do not hesitate to share it. I am grateful for your time. Come back soon.

Book Appointment